A customer is trying to boot an operating system that is installed on the eUSB on a Cisco UCS B-Series blade server; however Cheap Lucas Biglia Jersey , the boot fails. What is the cause of this failure?
A. The local disk must be the first device in the boot order. B. eUSB is not a supported boot device. C. eUSB support is available only on the Cisco UCS C-Series rack server. D. eUSB is not the first device in the boot order for the server.
Answer: D
Question: 2
A customer is troubleshooting degraded DIMM errors on a Cisco UCS blade server and would like to reset the BMC. What is the correct command sequence to reset the BMC?
A. UCS1-A# server xy UCS1-A chassisserver # scope bmc UCS1-A chassisserverbmc # reset UCS1-A chassisserverbmc* # commit-buffer B. UCS1-A# server scope UCS1-A chassisserver # scope bmc UCS1-A chassisserverbmc # reset UCS1-A chassisserverbmc* # commit-buffer C. UCS1-A# scope server xy UCS1-A chassisserver # scope bmc UCS1-A chassisserverbmc # reset UCS1-A chassisserverbmc* # commit-buffer D. UCS1-A# scope server xy UCS1-A chassisserver # scope bmc UCS1-A chassisserverbmc* # commit-buffer
Answer: C
Question: 3
Which commands can you enter to see if a component in the Cisco UCS domain generated a core file?
A. 6100-A# scope monitoring 6100-A monitoring # scope sysdebug 6100-A monitoringsysdebug # show cores Core Files: Name Fabric ID ---------- --------- B. 6100-A# scope sysdebug 6100-A sysdebug # scope monitoring 6100-A sysdebugmonitoring # show cores Core Files: Name Fabric ID ---------- --------- C. 6100-A# scope system 6100-A system # scope monitoring 6100-A systemmonitoring # show cores Core Files: Name Fabric ID ---------- --------- D. 6100-A# scope cores 6100-A cores # show cores Core Files: Name Fabric ID ---------- --------- E. 6100-A# scope logging 6100-A logging # scope monitoring 6100-A loggingmonitoring # show cores Core Files: Name Fabric ID ---------- ---------
Answer: A
Question: 4
Which four tech support files can you create with the Cisco UCS Manager that you can submit to Cisco TAC for support? (Choose four.)
A. UCSM B. disk LUNs C. fabric extender D. memory E. rack server F. chassis G. server cache
Which protocols can be used to send to Cisco TAC (Technical Assistance Center) the show tech-support command output information about the Cisco UCS domain? (Choose two.)
The Cisco UCS Manager displays FSM information for which four of these? (Choose four.)
A. which FSM task is being executed B. the current state of an FSM task C. the status of the previous FSM task D. any error codes returned while processing E. all completed FSM tasks F. multiple FSM tasks that completed over multiple tries G. multiple FSM tasks that failed
How will the Cisco UCS Manager react when all of the FSM tasks fail?
A. retries for 60 seconds B. raises faults and alarms C. restarts from the previous known good task D. sends an NOC SNMP trap email
Answer: B
Question: 8
What should you do when you see faults during the initial setup and discovery process?
A. Take note and address the faults. B. You can safely ignore these faults. C. Log them and try to address the first one. D. Reboot until the error messages go away.
Answer: B
Question: 9
When using the Cisco UCS Manager GUI to troubleshoot a suspected bad memory Cheap Keisuke Honda Jersey , which logs contain data that are related to the faulty DIMM?
A. the System Event log and Faults log that are located under the Admin tab B. the Events log and Faults log that are located under the Admin tab C. the System Event log that is located under the Server tab in the Navigation panel and the Faults log that is located under the Admin tab D. the System Event log that is located under the Equipment tab and the Faults log that is located under the Admin tab
Answer: D
Question: 10
Which three are valid tech support bundles to collect in the local management shell? (Choose three.)
A. UCSM B. UCSM-MGMT C. Port-Channel D. Adapter E. SAN F. FEX
Universe-Forum
Thema drucken
18.03.2020 07:51
Antworten
